Current Connecticut PSI format: the P-2 Unlimited Journeyperson Plumber exam has 70 questions, 2½ hours, and a 70% passing requirement. PSI lists the exam as open book and allows candidates to bring approved reference materials prepared under PSI rules.
What Is the Connecticut P-2 Journeyperson Plumber Exam?
The Connecticut P-2 examination is the trade test for the Unlimited Journeyperson Plumber license regulated by the Connecticut Department of Consumer Protection and administered by PSI.
The exam covers plumbing regulations, gas systems, cleanouts, fixtures, water heaters, piping and controls, water supply, supports, drain-waste-vent systems, backflow, traps, developed length, isometrics, joints, safety, and water treatment.
Short answer: the current PSI exam contains 70 questions, allows 2½ hours, requires 70 percent to pass, and is open book.
Drain, Waste, and Vent is the largest individual subject with 11 questions. Isometric Analysis and Fixtures and Equipment each carry 6 questions, while Gas Systems and Water Supply each carry 5.
This guide combines current PSI testing information, Connecticut DCP licensing requirements, code-reference guidance, plumbing math, isometric practice, and structured contractor exam prep without pricing.
Connecticut P-2 Journeyperson Plumber Exam Domains
Match your plumbing exam prep time to the current 70-question PSI outline.
| PSI Exam Area | What It Covers | Questions |
|---|---|---|
| Drain, Waste, and Vent | Drainage, venting, fixture-unit concepts, traps, slopes, cleanouts, layouts and related code rules | 11 |
| Isometric Analysis | Reading plumbing isometrics, developed length, layout interpretation and sizing relationships | 6 |
| Fixtures and Equipment | Fixtures, installation requirements, clearances, equipment and connections | 6 |
| Gas Systems | Fuel-gas concepts, piping, safety and related approved references | 5 |
| Water Supply | Water distribution, sizing, pressure, supply piping, valves and related code rules | 5 |
| Remaining Plumbing Topics | General regulations, cleanouts, water heaters, controls, hangers, backflow, traps, developed length, joints, safety and water treatment | 37 combined |
The five largest categories above account for 33 of the 70 questions. Use them as priority areas while still covering the complete PSI blueprint.
Research Authority and Verification Snapshot
The strongest Connecticut plumbing claims were checked against the current PSI plumbing bulletin, Connecticut DCP licensing pages, Connecticut DAS building-code information, and current 1 Exam Prep course information.
| Verified Point | Authority Count | Controlling Source |
|---|---|---|
| 70 questions / 2½ hours / 70% passing | Primary-source verified | Current PSI Plumbing Trades Candidate Information Bulletin |
| Open-book exam and permanent-tab rules | Primary-source verified | Current PSI bulletin |
| P-2 scope and apprenticeship qualification | Primary-source verified | Connecticut Department of Consumer Protection |
| Equivalent path: 8,000 OJT / 576 classroom hours | Primary-source verified | Connecticut DCP |
| 2022 Connecticut State Building Code uses 2021 IPC | Primary-source verified | Connecticut DAS / Office of State Building Inspector |
| P-2 topic weights and reference list | Primary-source verified | Current PSI bulletin |
About impressions: private Google Search Console impressions are not public. This authority snapshot reports source verification, not invented traffic, backlink, ranking, or Domain Authority metrics.
Connecticut Journeyperson Plumber Exam Breakdown
The P-2 licensing path combines Connecticut DCP eligibility, PSI testing, approved open-book references, plumbing trade knowledge, and post-exam licensing follow-through.
P-2 Trade Exam
70 questions | 2½ hours | 70% to pass
Testing Provider
PSI Services LLC
Licensing Authority
Connecticut Department of Consumer Protection
Exam Format
Computer-based and open book
Largest Topic
Drain, Waste, and Vent | 11 questions
Current Connecticut Code
2022 Connecticut State Building Code based on the
2021 International Plumbing Code with Connecticut amendments
PSI IPC Reference
PSI currently lists International Plumbing Code editions
including 2015, 2018 or 2021
Equivalent Experience Path
8,000 on-the-job hours + 576 classroom hours
P-2 Work Scope
Unlimited plumbing and piping work while employed by
a properly licensed contractor
Practice like the real PSI exam. Use your approved references during timed study so code lookup becomes part of your exam routine.
Know the IPC structure. Practice chapter, section, table, definition, and index lookup.
Prepare your references correctly. PSI allows permanent tabs and pre-exam annotations, but not writing during the exam.
Prioritize the heavy domains. DWV, isometrics, fixtures, gas systems, and water supply deserve extra exam prep time.
Plumbing Calculations, Isometric Analysis and Code Lookup Strategy
The Connecticut P-2 exam rewards candidates who can recognize the plumbing topic, locate the correct code rule, interpret isometric drawings, and complete calculations without burning through the clock.
Simplified study illustration for DWV, isometric, water-supply and gas-system practice.
Train each practice question as a lookup sequence: identify the system, choose the likely code chapter or reference, find the governing table or section, solve the problem, verify the rule, and move on.
- Drain, Waste, and Vent: 11 questions.
- Isometric Analysis: 6 questions.
- Fixtures and Equipment: 6 questions.
- Gas Systems: 5 questions.
- Water Supply: 5 questions.
| Skill | What to Practice | Common Mistake |
|---|---|---|
| Code navigation | Index terms, chapters, sections, tables, definitions and Connecticut amendments | Knowing the topic but not where to find the rule |
| Drain, waste and vent | Sizing, slopes, traps, vents, cleanouts, fixture units and layout | Using the wrong table or overlooking system conditions |
| Isometric analysis | Developed length, branch relationships, fixture connections and drawing interpretation | Reading a drawing as a flat plan instead of a piping layout |
| Water supply | Sizing, demand, pressure, distribution and backflow | Ignoring the conditions that affect sizing or protection |
| Gas systems | Fuel-gas references, piping, safety and installation rules | Looking only in the plumbing code when the PSI reference list points to NFPA material |
| Time management | Timed blocks, flag-return strategy and 150-minute stamina | Spending too long on one lookup or calculation |
Practice the path, not only the answer. After every missed exam-prep question, record the subject, code section or reference, calculation method, and reason the original answer failed.
Your Connecticut Journeyperson Plumber Licensing Roadmap
Seven steps take you from P-2 eligibility to PSI testing and Connecticut licensing follow-through.
1
Confirm P-2 eligibility
Complete a registered apprenticeship program or qualify through equivalent experience and training accepted by Connecticut DCP.
2
Document equivalent training when applicable
For the equivalent-experience route, Connecticut DCP lists 8,000 on-the-job training hours and 576 classroom hours for P-2.
3
Review the current PSI bulletin
Confirm exam format, current reference editions, testing rules, approved calculators, and permanent-tab requirements.
4
Prepare with Connecticut plumber exam prep
Study the PSI topic weights, practice code navigation, strengthen plumbing math, and complete isometric analysis.
5
Complete timed practice
Use mixed-topic questions and realistic 150-minute sessions so your prep matches the pace of the actual exam.
6
Take the PSI P-2 exam
Bring approved references, use a flag-and-return strategy, and manage code lookups, isometrics, and calculations carefully.
7
Complete Connecticut licensing follow-through
After passing, follow the score-report and licensing instructions from PSI and Connecticut DCP.
What Is on the Connecticut P-2 Plumber Exam?
Study according to the current 70-question PSI outline. The bars show each category relative to the largest subject.
Drain, Waste, and Vent
11 questions
Isometric Analysis
6 questions
Fixtures and Equipment
6 questions
Gas Systems
5 questions
Water Supply
5 questions
General Plumbing Regulations
4 questions
Cleanouts
4 questions
Hangers and Supports
4 questions
Traps and Interceptors
4 questions
Joints and Connections
4 questions
Piping, Valves, Controls
3 questions
Backflow
3 questions
Developed Length
3 questions
Safety and Excavation
3 questions
Water Treatment
3 questions
Water Heaters
2 questions
Current Connecticut P-2 Exam References
PSI lists the following references for the P-2 examination. Candidates bring their own approved materials and should verify the newest bulletin before testing.
| Reference | Primary Use | Current Exam Note |
|---|---|---|
| International Plumbing Code | Core plumbing code topics across the P-2 blueprint | PSI currently lists 2015, 2018 or 2021 editions |
| NFPA 54 National Fuel Gas Code | Fuel-gas piping and related requirements | PSI-listed reference |
| NFPA 58 Liquefied Petroleum Gas Code | LP-gas requirements | PSI-listed reference |
| 29 CFR Part 1926 OSHA | Safety and excavation | Latest available amendments or PSI selections |
| Water Processing | Water-treatment material | PSI lists the 3rd Edition, 2000 |
| NFPA 56 | Cleaning and purging flammable-gas piping systems | Current edition listed by PSI |
Code-cycle distinction: Connecticut's currently adopted state building code uses the 2021 IPC with state amendments, while PSI separately lists the code editions allowed for the P-2 exam. Check both before test day.
How to Prepare Your Open-Book References
Winning reference habits
- Practice with the same approved references you plan to bring
- Use permanent tabs only where PSI allows them
- Highlight, underline and annotate before exam day
- Practice table and index lookup under a timer
- Know where DWV, water supply and fixture rules live
- Complete timed exam prep under the full 150-minute limit
Avoid these exam-prep mistakes
- Using temporary Post-it tabs
- Planning to write in references during the exam
- Adding loose papers to approved books
- Writing question-and-answer sets into references
- Studying only one plumbing subject
- Spending too long on one code lookup
Current PSI rule: approved references may be highlighted, underlined, annotated, and permanently indexed before the examination, but candidates may not write in them during the test.
P-2 Journeyperson License vs P-1 Plumbing Contractor
The Connecticut P-2 Unlimited Journeyperson Plumber license is an individual trade credential. The P-1 Unlimited Plumbing Contractor license is the contractor-level credential.
Connecticut DCP states that a P-2 holder may do plumbing and piping work only while employed by a contractor licensed for that work. P-1 applicants normally qualify with two years as an unlimited licensed journeyperson or equivalent experience and training.
That means a candidate searching for Connecticut Journeyman Plumber contractor exam prep should understand the distinction: P-2 is the journeyperson trade exam, while P-1 is the contractor classification and carries separate contractor testing requirements.
Connecticut P-2 Journeyperson vs P-1 Plumbing Contractor
These licenses are connected, but they are not interchangeable.
| Path | Focus | Important Note |
|---|---|---|
| P-2 Unlimited Journeyperson Plumber | Individual journeyperson plumbing license | Works while employed by a properly licensed contractor |
| P-1 Unlimited Plumbing Contractor | Contractor-level plumbing license | DCP lists two years as an unlimited licensed journeyperson or equivalent experience and training for exam qualification |
| PSI P-2 Trade Exam | Plumbing trade knowledge and approved-reference research | Journeyperson candidates pass the trade portion |
| Contractor Business and Law | Business, law and project-management topics | PSI requires contractor candidates to pass business and trade portions |
| Contractor Exam Prep | Study, practice, code navigation, isometrics and exam strategy | Study support, not a state-issued license |
Connecticut P-2 Journeyperson Plumber Licensing Requirements
P-2 Applicant
Eligibility Path
- Complete a registered apprenticeship program or approved equivalent experience and training
- Equivalent-experience path lists 8,000 on-the-job hours
- Equivalent-experience path lists 576 classroom hours
- Follow current DCP documentation requirements
PSI Exam Candidate
Exam Prep Focus
- 70 questions
- 2½-hour examination
- Open-book approved references
- Timed code navigation, plumbing math and isometric analysis
Future P-1 Contractor
Contractor Path
- P-1 is the Unlimited Plumbing Contractor credential
- DCP lists two years as an unlimited licensed journeyperson or equivalent experience for exam qualification
- Contractor candidates must meet PSI business and trade testing requirements
- Follow current Connecticut DCP contractor rules
Six-Week Connecticut P-2 Study Plan
Use the PSI weights to balance DWV, isometrics, fixtures, water supply, gas systems, code navigation, math and full-length practice.
Week 1
PSI Blueprint and References
- Review all 16 domains
- Organize approved references
- Take a diagnostic exam
- Start a missed-question log
Week 2
Drain, Waste and Vent
- Drainage sizing
- Venting
- Traps and cleanouts
- Fixture units and slopes
Week 3
Isometrics and Fixtures
- Isometric reading
- Developed length
- Fixture connections
- Installation requirements
Week 4
Water and Gas
- Water supply
- Backflow
- Gas-system references
- Piping, valves and controls
Week 5
Math, Safety and Code Lookup
- Plumbing calculations
- OSHA review
- Water treatment
- Timed lookup drills
Week 6
Simulation
- Full mixed-topic practice
- 150-minute pacing plan
- Weak-area review
- PSI rule check
How Hard Is the Connecticut P-2 Plumber Exam?
The challenge is the combination of 70 questions, 16 plumbing subject areas, open-book code research, isometric analysis, calculations, and a 2½-hour time limit.
Common avoidable problems include weak DWV prep, slow reference lookup, misunderstanding isometrics, using the wrong code table, and spending too long on one problem. Structured contractor exam prep turns those weak spots into specific practice goals.
Connecticut P-2 Exam Day Checklist
Do this
- Arrive according to current PSI check-in instructions
- Bring valid identification required by PSI
- Bring only approved reference materials
- Use permanent tabs rather than temporary tabs
- Use a flag-and-return strategy for slow questions
- Manage time against the 150-minute limit
Do not do this
- Bring loose papers in your references
- Write in references during the exam
- Bring temporary Post-it tabs
- Depend only on memorized practice answers
- Ignore small blueprint categories
- Assume P-2 is the same as P-1 contractor licensing
After You Pass the Connecticut P-2 Exam
PSI's current plumbing bulletin directs candidates to submit the licensing fee indicated on the passing score report, together with passing score reports, to the Connecticut Department of Consumer Protection.
Keep your eligibility, apprenticeship or equivalent-experience documentation organized and follow the latest DCP instructions for the license process.
If your long-term goal is the P-1 Unlimited Plumbing Contractor license, remember that P-1 is a separate contractor credential with additional experience and testing requirements.
Connecticut Journeyperson Plumber Exam Prep Options
Select preparation that builds plumbing-code knowledge, approved-reference navigation, calculation accuracy, isometric skill, mixed-topic recall, and testing endurance.
Connecticut Journeyman Plumber Exam Prep Package
2021 IPC Package
- 2021 International Plumbing Code
- Permanent quick-reference tabs
- Journeyman Plumber study guide
- 750 practice questions with answer keys
- OSHA, IPC, fuel-gas, isometric and plumber-math review
2026 Study Guide and Online Course
Guided Video Prep
- 700+ practice questions
- 8+ hours of video training
- IPC chapter instruction
- Isometric walkthroughs
- Simulated computer-based exams
Complete Books, Tabs and Course Package
Complete Prep System
- Code book and permanent tabs
- Study guide and practice questions
- Online course and simulations
- 200 flash cards
- Mobile-friendly study access
Use the Correct Connecticut Plumbing Credential
Journeyperson exam prep prepares an individual for the P-2 plumbing trade examination. It does not itself create a P-1 plumbing contractor license.
· P-2 is the Unlimited Journeyperson Plumber license
· PSI administers the current 70-question P-2 trade exam
· Connecticut DCP determines license eligibility
· P-1 is the separate Unlimited Plumbing Contractor credential
Choose the credential first, then choose the exam prep that matches it.
Connecticut Journeyman Plumber Contractor Exam Prep FAQ
Connecticut P-2 Exam Basics
The current PSI Connecticut plumbing bulletin lists
70 questions for the P-2 Unlimited Journeyperson Plumber examination.
PSI allows 2½ hours for the 70-question
P-2 Unlimited Journeyperson Plumber examination.
The current PSI bulletin lists a minimum passing score
of 70 percent.
Yes. PSI lists the P-2 examination as open book.
Candidates bring their own approved references and must
follow PSI rules for annotations and tabs.
Yes. PSI permits permanent tabs or indexing completed
before the exam. Temporary tabs such as Post-it notes
are not allowed.
No. PSI states that reference materials may be highlighted,
underlined, annotated, or indexed before the exam,
but candidates may not write in the references
during the examination session.
The current PSI plumbing bulletin lists the International
Plumbing Code, including the 2015, 2018, or 2021 editions,
among the allowed references. Candidates should always
verify the newest PSI bulletin before test day.
The current 2022 Connecticut State Building Code adopts
the 2021 International Plumbing Code with Connecticut amendments.
Drain, Waste, and Vent is the largest individual subject area
in the current PSI P-2 outline with 11 questions.
The current PSI P-2 content outline assigns
6 questions to Isometric Analysis.
Licensing, References and Exam Prep
Connecticut DCP states that P-2 candidates qualify through
completion of a registered apprenticeship program or equivalent
experience and training. For the equivalent-experience path,
DCP lists 8,000 on-the-job training hours and 576 classroom hours.
P-1 is the Unlimited Plumbing Contractor license.
P-2 is the Unlimited Journeyperson Plumber license.
A P-2 license holder may perform plumbing and piping work
only while employed by a contractor licensed for that work.
PSI states that journeyperson candidates are required to pass
only the trade portion for licensure, while contractor candidates
are required to pass both trade and business portions.
Start with Drain, Waste, and Vent, then Isometric Analysis
and Fixtures and Equipment. Follow the full PSI outline
so smaller subjects are not ignored.
The current PSI bulletin lists the International Plumbing Code,
NFPA 54, NFPA 58, OSHA 29 CFR Part 1926,
Water Processing, and NFPA 56 among the allowed P-2 references.
Study by the PSI topic weights, practice code navigation
with the approved references, work plumbing math and
isometric problems, complete timed practice questions,
and review every missed question by topic and reference location.
1 Exam Prep Journeyman Plumber Exam Prep Video
Explore Connecticut Journeyman Plumber Resources
Use current Connecticut and PSI sources together with focused contractor exam prep for the complete P-2 licensing path.
Ready to Prepare for the Connecticut P-2 Plumber Exam?
Build plumbing-code knowledge, open-book navigation, DWV skill, isometric-analysis speed, water-supply and gas-system knowledge, plumbing math accuracy, and full-length testing endurance for the current Connecticut PSI P-2 examination.
Questions?
Call 877-775-9400
or email
sales@1examprep.com
- Choosing a selection results in a full page refresh.
- Opens in a new window.